 |
Cationic UV curable systems, such as UV15, tend to have much higher temperature resistance than other UV type formulations. Its glass transition temperature (Tg) with a straight UV cure is 90-95°C, and when post cured for 30 minutes at 125°C, the Tg is 125-130°C. This post cure also enhances UV15’s chemical resistance. The service temperature range for this optically clear system is -80°F to +350°F. It has a low viscosity, can be applied with a syringe and it has the ability to be spin coated.
|
|
UV21: One Component System with Outstanding Flexibility
|
|
|
Well suited for bonding, sealing, coating, encapsulation and formed-in-place gasket applications, UV21 has a low Shore A hardness and an exceptionally fast fixture speed. Its softness allows it to be
more easily reworked when compared to most other UV cure systems. This optically clear compound has a high viscosity and bonds well to a wide variety of substrates.
For more information, request a data sheet on UV21
|
|
|
MB306: Low Viscosity Methyl Cyanoacrylate
|
|
|
MB306 is an instant setting system where the rate of is cure dependent upon the humidity—the higher it is, the faster the cure. This low viscosity, one part compound offers high tensile lap shear strength to a wide variety of substrates including metals, rubbers and plastics. It has good chemical resistance, especially to cleaning agents.
For more information, request a data sheet on MB306
|
|
|
LED401 White: Opaque LED Curable System
|
|
|
The uniqueness of LED401 White is its opaque white color which adds a special dimension to light initiated curing systems, since nearly all are either transparent or tinted with dyes. This one part system cures fully tack-free upon exposure to a 405 nm wavelength light source. It offers dimensional stability and superb electrical insulation properties.
For more information, request a data sheet on LED401 White
|
|
|
Supreme 3HT-80: One Part Epoxy Adhesive Cures At 80°C
|
|
|
Supreme 3HT-80 is a high strength, one component epoxy that features a 30 minute cure at 175°F (80°C) and a 10 minute cure at 250°F (121°C). It is well suited for difficult applications in the aerospace, electronic, electrical, computer and chemical industries. Supreme 3HT-80 is ideal for bonding and can withstand rigorous thermal cycling.
For more information, request a data sheet on Supreme 3HT-80
|
|
|
UV15-7DC: Dual Cure System for Shadowed Out Areas
|
|
|
Enabling cures in shadowed out areas, UV15-7DC features a primary cure utilizing UV light and a secondary cure that requires heating for curing sections that are not exposed to UV light. This system has superior physical strength properties, low shrinkage upon cure and good non-yellowing characteristics. It also offers excellent dimensional stability, superb electrical insulation properties and a very good capacity to withstand thermal cycling.
For more information, request a data sheet on UV15-7DC
|
|
|
EP65HT-1: Fast Curing & Withstands Chemicals
|
|
|
Combining ultra-fast cures and high temperature resistance, Master Bond EP65HT-1 is a two component epoxy that sets up in 3-5 minutes and has a glass transition temperature of 125°C. It features superior electrical insulating properties and strong chemical resistance while meeting NASA low outgassing specifications. This high performance compound bonds well to a wide variety of substrates and is widely used in the electrical, electronic, appliance, computer, optical, automotive and OEM industries. EP65HT-1 is easy to apply and is available for use in gun applicators.
For more information, request a data sheet on EP65HT-1
|
|
 newsletters@masterbond.com
 +1 201 343 8983
Copyright  2014 by Master Bond Inc. All Rights Reserved. This content may not be reproduced in any way without the prior written permission of Master Bond Inc.
|
|
|
|
View this email online
July 2014
